equipment reviews
This Month's Featured Equipment Reviews
Merrill Audio THOR Mono Block Amplifiers Review
Plinius Hautonga Integrated Amplifier Review
KEF R700 Loudspeaker Review
Marantz SA-14S1 SACD Player & DSD DAC Review
Genesis G7c Loudspeakers
Latest AV News
Flat Panel HDTV Forum Topics:
Classic Flat Panel HDTV Reviews
Past Plasma HDTV News
 
Pioneer Electronics PureVision Elite PRO-930HD Plasma HDTV  Print E-mail
Home Theater Flat Panel HDTVs Plasma HDTVs
Written by Adrienne Maxwell   
Tuesday, 01 August 2006
Article Index
Pioneer Electronics PureVision Elite PRO-930HD Plasma HDTV 
Page 2
Page 3

Introduction
As we inch closer to the DTV transition, many television manufacturers are hedging their bets as to which display technology—plasma, LCD or micro-display—will ultimately win our hearts and checkbooks. Some companies have chosen to offer both plasma and LCD flat panels; others can’t even narrow it down that much, bringing out product in every new display category.

Pioneer has taken a road less traveled. The company is quite content to put all of its eggs in the plasma basket. (Okay, I’m done with the platitudes.) They no longer manufacture rear-projection TVs of any kind, nor do they offer panels smaller than 42 inches, since that would essentially require them to give LCD a serious look. As I write this, the Pioneer website lists a total of nine TVs on the roster, all plasmas ranging from 42 to 61 inches.

If all you do is plasma, then you had better do it well. The new 43-inch PRO-930HD ($4,500) is confirmation that Pioneer knows how to bring out the best in this technology. This 1,024 x 768-pixel panel, part of the Elite line, is a true HDTV: It has built-in ATSC, NTSC and QAM tuners, as well as a CableCARD slot. It adheres to Pioneer’s minimalist design approach, sporting an all-black frame with a gorgeous high-gloss finish and a trim profile, thanks in part to the detached speakers. Without the two 13-watt speakers in place, the panels weighs 56.9 pounds and measures just 24.9 inches high by 42.375 wide by 3.625 inches deep. A tabletop stand is supplied, and wall-mounting hardware is sold separately.

Set-up
Another reason for the PRO-930HD’s trim profile is that Pioneer has put the connection panel in a separate box that goes in your equipment rack. A proprietary cable links the plasma to this media receiver, as they call it. The two-piece design allows for a cleaner look, since only the power cord and proprietary cable are attached to the panel itself, and it’s much easier to connect external equipment directly to the receiver. The IR port is on the panel, so you can tuck the media receiver away in a cabinet. Yet another benefit to this approach is that you can use shorter cables, which saves money and can improve the signal quality, especially with a digital video signal like HDMI.

Speaking of HDMI, the PRO-930HD has two of them—inputs, that is. It also has two iLink ports and three component video inputs, one of which is placed on the media receiver’s front panel, a decision gamers will likely appreciate. It’s worth noting that Inputs 1 and 3 on the back panel share a component video and HDMI input, so you have to choose one or the other via the onscreen setup menu. The default setting is component video for Input 1 and HDMI for Input 3. The media receiver also has an RS-232 port to incorporate the TV into an automation system, a 15-pin RGB connector for use with a computer and a PCMCIA Type II memory-card adapter that lets you display JPEG photos and slide shows.

Making basic adjustments to the PRO-930HD’s video and audio parameters is a straightforward process. The owner’s manual thoroughly explains the different choices, the onscreen menu is translucent and logically laid out, and the individual video controls don’t cover the screen, which makes it easier to adjust the picture. I began with video adjustments, setting up the HDMI and component video inputs using my Sony DVP-NS75H DVD player and test patterns from the “Video Essentials” DVD (DVD International). Pioneer has included six picture modes from which to choose: Standard, Dynamic, Movie, Game, User and Pure (which Pioneer says “reflects input signals as faithfully as possible”). In all modes but Dynamic, you can make further adjustments to contrast, brightness, color, tint and sharpness. I recommend you avoid the Dynamic mode; it’s extremely blue and shows a ton of edge enhancement. I ultimately went with the Pure mode for the HDMI input and the Movie mode for component video. Both look quite accurate by videophile standards and required only minor tweaks on my part. Some edge enhancement was still visible in these modes, which required turning down the sharpness control. You can turn this setting all the way down through the HDMI input; however, with component video, the picture gets noticeably softer if you set the sharpness control at its minimum (–15). I set it at –1 to remove edge enhancement yet still show all the detail in the picture. In addition to the above six picture modes, the PRO-930HD come ISFccc calibration ready, which adds two additional viewing modes, ISF day and ISF night. This calibration should be performed by a professional for further adjustment of the plasma's picture contrast, tint, color as well as to take into account the specific room environment.

A host of advanced color controls allows you to fine-tune the picture even further. You can choose from five color temperature modes (five presets, plus a manual mode that should only be used by a professional calibrator); the Low mode was my choice, as it is the closest to the 6,500-Kelvin standard. Color Management allows for individual adjustments of the red, green, blue, yellow, cyan and magenta points. Other controls include CTI (Color Transient Improvement), digital and MPEG noise reduction and Dynamic Range Extender features that let you alter black level, contrast and gamma. I turned all of these features off for my review.

On the audio end, should you choose to attach the supplied speakers, be prepared to put some effort into it. This isn’t a snap-and-go procedure, as evidenced by the fact that a separate manual is devoted to the process. You can mount the speakers flush with the cabinet or with a small gap. Both the speakers and plasma use spring-loaded connection terminals for the speaker wire. The audio set-up menu includes controls for treble, bass and balance, plus options for SRS Focus control, SRS simulated surround sound and TruBass bass enhancement. A subwoofer output is aboard to send bass to a separate subwoofer. If you’d rather send all audio signals coming in from the tuners to your A/V receiver, there’s also an optical digital audio output.

Now about those tuners …This is the only area where set-up and operation aren’t as intuitive as they could be. Given that this is a higher-end display, perhaps Pioneer is betting that most people will forego the use of the internal tuners for an external cable or satellite set-top box, but you can never rule out some people’s preference for getting free over-the-air HDTV content. Of the two RF inputs on the media receiver’s back panel, you must use Antenna A for HDTV and Antenna B for cable, and you have to run a separate scan for each antenna. During the scanning process, the onscreen display doesn’t indicate which or how many channels you have tuned. Once the scan is complete, you’re given a list of successfully tuned channels, but there’s no way to access this list again to quickly add or delete channels. There is an “Add Channel” feature in the set-up menu, but it’s oddly conceived and difficult to use. Clearly, Pioneer intends for you to use the TV Guide onscreen interface to manage your channels, but this doesn’t group HDTV channels together. In conjunction with my Terk HDTVi antenna, the internal ATSC tuner picked up most of the HDTV stations in my area, although it never did find the local PBS HD channel. The QAM tuner picked up the first 99 channels in my digital cable system without needing a cable box.

The picture-in-picture function is also a bit confusing. You can watch an antenna and external source in regular PIP fashion or in several different split-screen options, but it’s a good idea to read the manual for an exact explanation of how the function works. On the supplied remote, PIP is accessed via the “Split” button. Beyond that odd nomenclature, I like the remote. It’s bulky, but it’s backlit and has dedicated buttons to access each input, change the screen size and scroll through the picture modes. The PRO-930HD scores points for including automatic aspect ratio detection and the ability to change the aspect ratio of HD sources.


 
HDTV Guide Advert

 
  home theater news  |  equipment reviews 
  blu-ray reviews  |  dvd  |  theatrical reviews  
  music download reviews  |  music disc reviews
  contact  |  about-us  |  careers   |  brands 
  Subscribe to Us   |   RSS   |  AVRev Forums
  front page  |  virtual tours  |  dealer locator
  how to features  |   lifestyle & design articles
  Want Your Home Theater Featured on MHT?
   CE Partners: HDD  |  HDF  |  VGT  |  SD  |  DVD
   
  Click Here to Advertise with Us | Specs
  Sponsors | privacy policy | terms of use
  909 N. Sepulveda Blvd. El Segundo, CA 90245
  Ads: 310.280.4476 | Contact Us
  Content: 310.280.4575 | Mike Flacy